Weil-McLain SlimFit Bedienerhandbuch Seite 45
- Seite / 128
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Part number 550-100-116/0714
45
SlimFit
™
COMMERCIAL CONDENSING GAS-FIRED WATER BOILER
— Boiler Manual
DIRECT VENT — Vertical
&IGURE Vertical direct vent terminations (air termination can be vertical or sidewall as shown below)
5SEONLYTHEVENTAIRPIPINGMATERIALS
ANDKITSLISTEDIN&IGUREPAGE
.
Read and follow all instructions in this
manual. $/./4PROCEEDWITHVENTAIR
PIPINGINSTALLATIONUNTILYOUHAVEREAD
PAGE through page 33 and PAGE
through PAGE.
Locate the termination such that the total
vent piping from the boiler to the termi-
nation
WILL NOT EXCEED THE MAXIMUM
LENGTHGIVENIN&IGUREPAGE
.
#OMPLYWITHALLVENTSYSTEMMANUFAC-
turer’s instructions.
Provide a vent manufacturer’s SlimFit Vent
Adapter and reducer (if needed) at the boiler
vent connection.
Every joint on POLYPROPYLENEVENTPIP-
ing
MUST include a locking collar. Failure to
supply locking collars could result in vent/
air piping leakage.
Determine termination location
1. e vent and air terminations must be installed as shown in
Figure43. e air termination can be either through the roof or
through a side wall, as shown.
2. e termination placement must comply with clearances and
limitations shown in Figure31, page36.
3. Locate the terminations so they are not likely to be damaged by
foreign objects, such as stones or balls, or subject to buildup of
leaves or sediment.
4. Provide means to access the boiler air inlet as instructed on
page46.
5. Install the boiler in a location that allows proper routing of all
vent and air piping from the boiler vent and air connections to
the selected termination locations.
Do not exceed the maximum lengths of the outside vent
and air piping shown in Figure44, page46. Excessive
length exposed to the outside could result in freezing of
condensate in the vent pipe or vent/air piping failure.
Follow vent/air pipe manufacturer’s instructions for
proper protection and support of the piping and for
installations in very cold climates.
Multiple vent terminations
1. When terminating multiple SlimFit boilers, terminate each vent
connection as described in this manual. When using sidewall air
terminations, place terminations at least 6inches apart.
Terminate all vent pipes at the same height and all air
pipes at the same height to avoid possibility of severe
personal injury, death or substantial property damage.
2. Place roof penetrations to obtain minimum clearance of 12inches
between edge of air intake elbow and adjacent vent pipe of another
boiler for U. S. installations (see Figure45, page46).
3. For Canadian installations, provide clearances required by CAN/
CSA B149.1 Installation Code and a ULCS636 compliant vent kit.
Install vent piping
See 7!2.).' about boiler vent/air outlet seals and
vent clamp on page29. Verify that the seal is installed
correctly before inserting the vent manufacturer’s
SlimFit Vent Adapter.
USE SWEEP ELBOWS FOR ALL VENT PIPING
WHEN POSSIBLE — Short-radius elbows cause
higher pressure loss, resulting in less allowable
vent/air piping length. See Figure 27, page 30
for maximum lengths and reductions required
for fittings.
1. Install the vent/air pipe manufacturer’s SlimFit Vent Adapter in
the boiler vent and air outlets. Follow all vent/air pipe manufac-
turer’s instructions.
2. Install a vent/air pipe manufacturer’s reducer if needed to adapt
to the vent size being used.
3. Slope vent piping toward the boiler slope vent piping a mini-
mum of ¼inch per foot in horizontal runs or larger per vent pipe
manufacturer’s instructions.
4. Support piping independently of the boiler Install pipe sup-
ports every 5feet on both the horizontal and vertical runs. Install
a hanger support within 6inches of any upturn in the piping. Or
follow vent/air pipe manufacturer’s instructions.
- Boiler Manual 1
- 3LIM&ITMODELNUMBERS 2
- Configuration options 3
- Electrical panel components 3
- Contents 4
- Hazard definitions 4
- Please read before proceeding 5
- Prepare boiler location 6
- Prepare boiler 10
- Prepare boiler (continued) 11
- Install water piping 14
- (continued) 15
- Multiple boiler water piping 22
- Commonwealth of Massachusetts 33
- DIRECT EXHAUST — Sidewall 37
- DIRECT EXHAUST — Vertical 39
- DIRECT VENT — Sidewall 43
- DIRECT VENT — Vertical 45
- Install condensate components 48
- Gas piping 49
- Gas piping (continued) 50
- Field wiring 51
- (cont.) 59
- Contractor log-in 60
- Analog input options 70
- High altitude installations 70
- MASTER boiler setup 71
- Sola control parameter table 72
- Startup — fill the system 87
- X100 inhibitor must be used 88
- Check/verify water chemistry 88
- Startup — final checks 89
- Startup procedure 90
- Startup procedure (continued) 91
- Part number 550-100-116/0714 95
- Operation screen (below) to 95
- General: 96
- Additional if combustion or 96
- Annual startup 97
- Annual startup (continued) 100
- Troubleshooting 103
- Troubleshooting (continued) 104
- — Boiler Manual 111
- Maintenance 112
- Maintenance (continued) 113
- Replacement parts 115
- Replacement parts (continued) 116
- Dimensions 124
- Dimensions (continued) 125
- Ratings — SlimFit boilers 126
- START-UP DATA 128
Verwandte Produkte und Handbücher für Warmwasserbereiter & Kessel Weil-McLain SlimFit
(64 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern